Duoplus 300wr user manual

Tet Feb 23,. Then bandwidth limiting is done by IP address transparently to the user.. Read All 11 Posts.. I'm a new Mac user. Yes it is connected wirelessly and its a Telkom duoPlus wr.. If you are a Windows user,. Existing user? Sign In. Remember me Not recommended on shared computers Sign in anonymously. Forgot your password? Or sign in with one of these. Quote saved. View saved quotes Close. Login to quote this blog Login Close. Failed to save quote.

Please try again later. Step 6: Click Next. Step 8: Select Yes or No to specify if you want to hide your wireless network name or not. Step 9: Click Next. This opens the System Password Page. Step Click Next. This opens the Summary page. Step Click Finish. Static To configure Ingress Layer 3: 1. The side effect is that a misconfigured stream can potentially take all bandwidth. CoS1 is not rate controlled hence the field is disabled.

CoS2 takes Kbps when there is no CoS1 packets. Only percentage can be assigned to the CoS2 - CoS6. CoS1 is not rate controlled hence the field is not displayed. If you choose Specify, you need to enter the protocol number in the box next to the Protocol field. A static route is a pre-defined pathway that network information must travel to reach a specific host or network. You can use static routing to allow different IP domain users to access the Internet through the router.

The RIP protocol regularly broadcasts routing information to other routers on the network. Packets are routed according to the packet's destination IP address. Below you will see an example of a basic routing table. To restrict access to the web interface, you need to set the System Password. To change the System Password: 1. Select Advanced Menu 2. Page Firmware Update When updating the firmware, make sure you are using the correct file for this router.

Use of a firmware that is not Telkom Approved will void the warrantee and may result in damage to your router. Once the upgrade is complete the router will reboot. You will need to log back into the router after the firmware upgrade is completed. SSID is wireless network name for the wireless router. Your wireless client needs this name to establish a wireless connection. The wireless setup allows the user to enable or disable the Access Point AP. The options listed can be changed to cater for advance users.

Wireless Configuration To access Wireless Setup: 1. Select the Wireless Menu. The SSID field takes up to 32 alphanumeric characters. This is to prevent unauthorized wireless users from accessing your router.

By default, WPA is selected. The unique default WPA key can be found on a label on the base of your router. Each radio network interface card NIC and router must be manually to use the same key.

Page WR User Manual It is a port-based network access control that keeps the network port disconnected until authentication is completed. WPA is an industry-supported, pre-standard version of WPA uses a sophisticated key hierarchy that generates new encryption keys each time a mobile device establishes itself with an Access Point.

It allows you to permit or ban devices by entering the MAC address or selecting devices that are currently connected. Select Wireless Management. This opens the Wireless Management page.

WDS network allows users of mobile equipment to roam and stay connected to the available network resources. Security settings must be the same in all Router in the WDS network. Note: WDS privacy is not supported in Crude mode. In this page, you can block specific traffic for example, block web access or any traffic from a host on your local network.

Page WR User Manual 3. Select the available rules for a given category. Click View to view the rule associated with a predefined filter. Click Add to apply the rule for this category.

If a rule is not in the list, you can create your own rule in the User category. If the URL contains a blocked keyword, then access to that website will be denied.

Depending on the severity level, the information log will generate log reports to a remote host if remote logging is enabled. The type of information forwarded to the remote computer depends on the Log level. Each log message belongs to a certain log level, which indicates the severity of the event. Notice Default Conditions that are not errors but might warrant special handling.

Info Events or non-error conditions of interest. Debug Software debugging message. Specify this level only when directed by a technical support representative. Modem Status Product Information This page displays the product information and software versions.

WDS Report Page of To access Help, select the Help Menu. Only qualified technical specialists are allowed to service the equipment. Observe safety precautions to avoid electric shock Check voltage before connecting to the power supply. Connecting to the wrong voltage will damage the equipment. Print page 1 Print document pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR.